8086 MICROPROCESSOR INTERFACING WITH 8255 PDF

0 Comments

Different Modes. • Interfacing Examples Using PPI microprocessors. ➢ There are 24 I/O pins of the 82C55A make it compatible with the 3. Microprocessors and Microcontrollers/Interfacing with Lecture .. PIO . • The parallel input-output port chip is also called as programmable. Microprocessor | (programmable peripheral interface) · Interface with Subtract content of two ports by interfacing with microprocessor.

Author: Mikale Tojagul
Country: Ethiopia
Language: English (Spanish)
Genre: Business
Published (Last): 12 May 2008
Pages: 329
PDF File Size: 20.16 Mb
ePub File Size: 13.43 Mb
ISBN: 598-8-63213-250-6
Downloads: 25546
Price: Free* [*Free Regsitration Required]
Uploader: Taugami

The port A address is h.

8255A – Programmable Peripheral Interface

Debugging a Program in Supporting Circuits of Microprocessor. The stepper motor has an internal delay of 10msec. Binary level pulses of v are required at its winding inputs to obtain the rotation of shafts. It is fastest technique.

An external feedback resister acts to microprocesspr the gain.

OK Programmable Interval Timer. Minimum Mode Configuration of Assume that the routine for this delay is already available. Reset out signal from clock generator is connected to the Reset signal of the CWR wity is 86h. Registration Forgot your password? Operating Modes of Motorola Pins and Signals. The CPU may drive these lines using output port lines in case of multichannel applications.

Related Articles  DIN 7991 TORX PDF

To use this website, you must agree to our Privacy Policyincluding cookie policy. The DAC find applications in areas like Digitally controlled gains Motor speed controls Programmable gain amplifiers etc. Interfacing with Features of Programmable Interrupt Controller.

An operational amplifier is used micropocessor a current — to — voltage converter at the output of AD The sequence of pulses can be decided, depending upon the required motion of the shaft.

Auth with social network: Code Code segment Start: Interfacing of with Ports A, B, and C can be individually programmed as input or output ports Port C is divided into two 4-bit ports which are independent from each other Mode 1: By using indirect address 855 this range can be extended upto 2 16 addresses. Share buttons are a little bit lower. Feedback Privacy Policy Feedback.

If you wish to download it, please recommend it to your friends in any social system. Pin Diagram of Port A acts as a 8-bit input data port to receive micrkprocessor digital data output from the ADC. Input Output Interfacing Techniques. About project SlidePlayer Terms of Service.

Your email address will not be published. Select your Language English.

Intel A Programmable Peripheral Interface

In this section we discuss many useful applications like keyboard and display interface, traffic light control, printer interface and so on. Modular Interfacint in Microprocessor. Out of these 8 inputs only one can be selected for conversion by using 3 address lines A,B,C.

Related Articles  ESSENCE OF THE UPANISHADS EKNATH EASWARAN PDF

My presentations Profile Feedback Log out. Maximum Mode Configuration of Leave a Reply Cancel reply Your email address will not be published. The stepper motor has rotor teeth. Features of Microprocessor. Address lines A 0 — A 1 are used by for internal decoding.

UNIT-IV 8255 PPI Various Modes Of Operation Interfacing To 8086.

To get absolute address, all remaining address lines A 3 — A 19 are used to decode the address for Only lower data bus D 0 — D 7 is used as is 8-bit device. To get absolute address, all remaining address lines A 15 — A 2 are used to decode the address for Design of Microprocessor-Based Systems Dr. It employs rotation of its shaft in terms of steps, rather than continuous rotation as in case of AC or DC motors.

With a pulse applied to the winding input, the rotor rotates by one teeth position or an angle x.